All Products

This is our products page. It contains a list of the main vibration control products, divided into categories, that are sold by Mason UK Ltd.

Click on “load more” to show further products in a category.

Architectural Products

  • All
  • Acoustic Foams
  • Architectural
  • Concrete Floating Floors
  • Floating Floors
  • Isolated Walls
  • Isolation Hangers
  • Jack-Up LDS Rubber Floating Floors
  • Jack-Up Spring Floating Floors
  • L.D.S Rubber Hangers
  • Lightweight Floating Floors
  • MFS Lightweight Floor Spring
  • Products
  • Rubber Mounts & Pads
  • Spring Hangers
  • Vibration Control

CWC-50 Acoustic Ceiling and Wall Clip

A cost-effective solution for vibration isolation and acoustic treatment of walls and ceilings, our new CWC-50 Clip is designed with ease of installation in mind.

Acoustic Floating Floors

Floating floors systems are used for many purposes, predominantly to prevent noise passing through the floor but also to isolate against vibration and impact

Concrete Floating Floors

Floating floors systems are used for many purposes, predominantly to prevent noise passing through the floor but also to isolate against vibration and impact.

MFS-B 25mm Deflection Floor Spring Mount

Our MFS spring mounts are available with higher deflection 25mm springs (titled MFS-B). Utilising our 30-B series springs enables the mounts to achieve lower natural frequencies and therefore improve isolation performance from typical gym activities, compared to the standard MFS mounts.

HDQF-A Rubber Ceiling Hangers

HDQF quick fit ceiling hangers use high quality low dynamic stiffness natural rubber. This hanger has been designed to aid the contractor with a quick and easy installation of suspended acoustic ceilings.

HD LDS Rubber Acoustic Ceiling Hangers

The HD range of hangers is one of our most popular anti-vibration hangers. The acoustic hanger uses a high quality low dynamic stiffness (LDS) natural rubber element which offers excellent acoustic sound isolation properties.

HDQF-X Spring Hanger

HDQF-X quick fit ceiling hanger (Spring Variant). This hanger has been designed to aid the contractor with a quick and easy installation of suspended acoustic ceilings.

30 Series – Acoustic Spring Hanger

The 30 hanger series can be fitted with a range of springs to suit acoustic and weight requirements. Spring hangers are used to isolate against low frequency noise from sources such as footfalls and mechanical vibration.

30N Series – Spring Hanger

The 30N hanger series can be fitted with a range of springs to suit acoustic and weight requirements. Spring hangers are used to isolate against low frequency noise from sources such as footfalls and mechanical vibration.

DNSB-A Sway Brace/Wall Tie

DNSB-A is a low frequency wall tie. This sway brace has a bolt end for stud walls or hooked end for masonry walls.

DNSB-BM Wall Tie/Sway Brace

This DNSB-BM is our most popular acoustic sway brace. It is a low frequency wall tie. You have a choice of a bolt end for stud walls or hooked end for masonry walls.

WIC Sway Brace/Wall Tie

The WIC acoustic wall tie is a low profile, low cost sway brace. Minimum cavity = 40mm

WIC-2-SM Sway Brace/Wall Tie

Type WIC-2-SM is a masonry wall tie designed to connect two masonry walls built together. There is no limit on wall thickness or cavity for this sway brace

WIC-2-90 Sway Brace/Wall Tie

The Type WIC-2-90 acoustic sway brace/wall tie is a 90-degree variant of our popular WIC product. It is designed to tie internal and external walls together. One side is designed to be imbedded into blockwork mortar joints, the other to be fixed into the opposing wall with suitable fixings.

DSSB – Double Spring Sway Brace/Slam Wall Isolator

The DSSB Double Spring Sway Brace/ Slam Wall Isolator is a specially designed product, which was first thought up to solve a problem, but become a popular solution for such constructions as slam/rebound walls. As a result of this popularity, we decided to add it to our vast product range.

HDLP-X Low Profile Ceiling Hanger

The HDLP-A Hanger (PREVIOUSLY CALLED THE CRCH-X) has been designed as a low profile ceiling hanger and is used where floor to ceiling heights are critical. It uses the same spring element as the 30-X and HDQF-X Hanger, and therefore has the same properties.

MFS-AJ Adjustable Floor Spring

The MFS-AJ is a jack specially built for attachment to joists and its used as part of a lightweight acoustic floating floor system. The ability to adjust the height gives it an advantage over the standard MFS when placing jacks on floors that aren’t level.

MFS-AF Adjustable Floor Spring

The MFS-AF is an acoustic floating floor jack specifically built for lightweight floors. The ability to adjust the height gives it an advantage over the standard MFS when placing jacks on floors that aren’t level.

MFS Lightweight Floor Spring

It is often necessary to provide an wooden acoustic floating floor rather than the heavier concrete construction with wood topping. Cost or weight restrictions may be the factor.

Dry and Formwork Acoustic Floor Systems

The best performing floating floor systems are typically heavy and thick, using a concrete layer, such as our jack up floating floors. However, sometimes this is undesirable, or not possible due to structural and building limitations, and a lightweight system is required.

AB-716 Angle Head Restraint

The AB-716 is an angled, head restraint for the top / and of block and stud walls.

NPS – Partition Support

NPS Partition Support isolates the bottom channel of steel stud walls. NPS is held in place by a frame or hammer fixing.

SWW Masonry Isolation

Mason’s SWW type acoustic wall isolation strips are designed to isolate a wall from the base slab. The SWW is designed to suit width and wall load.

AFA – Acoustical Furring Attachment

This AFA is a acoustical furring attachment for use with metal or wood stud walling. It uses a low dynamic stiffness natural rubber for effective isolation and the metal elements of the AFA are completely encapsulated.

Acoustic Isolation Products for Walls

It is important that the walls of a space sensitive to noise or vibration transmission are isolated from the main building structure. These acoustically isolated walls can be built on a floating floor or specially designed wall support plates.

Super W Pad

Super W pads feature unique waffle pockets which allow for greater deformation of the material, providing excellent isolation performance. Super W anti-vibration pads can be supplied in multiple configurations to suit most situations.

HDSM-X Spring Joist Hanger

Joist or wall hanger with 25mm deflection spring element. They can be fitted with a ceiling channel clamp or eye bolt.

HDLP-A Low Profile Ceiling Hanger

The HDLP-A Hanger (PREVIOUSLY CALLED CRCH) has been designed as a low profile ceiling hanger and is used where floor to ceiling heights are critical. It uses the same rubber element as the HD-A and HDQF-A Hanger, and therefore has the same properties.

HDSM-A Joist Hanger

Joist or wall hanger with double deflection LDS rubber element and can be fitted with a ceiling channel clamp or eye bolt.

DNHS – Acoustic Spring Hanger

The DNHS series of hanger features both a metal spring and an LDS rubber element. This provides acoustic isolation against both low and high frequency vibration.

HS – Spring Hanger

The HS series of spring hanger allows for a wide range of springs to be used to suit both acoustic and load requirements.

Jack-Up LDS Rubber Floating Floors

The Mason FSN Jack-Up acoustic floor system can be used as the crucial part of achieving box in box construction for studios or rooms requiring a high level of acoustic separation or simply providing acoustic or impact isolation from one area to another.

Jack-Up Spring Floating Floors

The jack up spring floating floor is used for low frequency isolation or where impact isolation is required, such as bowling alleys, gymnasia and health clubs.

WHR Acoustic Ceiling Hangers

The WHR is a low cost ceiling hanger which still provides 5mm of deflection and is constructed from high quality low dynamic stiffness natural rubber which has natural acoustic isolation properties.

NFS – Neoprene Foam Strip

Closed cell foams are used as part of an airborne acoustic barrier or a structural vibration break.

Isolation Hangers

Acoustic isolation hangers are an excellent way of preventing airborne noise from below passing into the building structure, or preventing noise/vibration from the floor above entering the room below.

Dry and Formwork Rubber Floating Floor

The Dry Rubber Floating Floor system is the traditional method of creating a floating floor. Isolators are placed at regular intervals across the area and the floating floor built on top.

Spring Hangers

Mason U.K. has a large range of spring hangers available to suit a wide variety of loads and acoustic requirements.

L.D.S Rubber Hangers

Acoustic, LDS (Low Dynamic Stiffness) rubber (previously neoprene) hangers can be used for suspending ceilings or mechanical plant.

Vibration Control Products

  • All
  • Air Springs
  • Inertia Bases
  • Lightweight Floating Floors
  • Products
  • Rubber Mounts & Pads
  • Spring Mounts
  • Vibration Control

Super W Pad

Super W pads feature unique waffle pockets which allow for greater deformation of the material, providing excellent isolation performance. Super W anti-vibration pads can be supplied in multiple configurations to suit most situations.

HG Grommets Bolt Isolation Bushings

HG Grommets are rubber bolt isolation washer bushings designed to allow a fixing to be passed through without compromising the benefits of an anti-vibration layer.

W Pad

Waffle pad is a thin anti-vibration mat featuring a series of square cut outs which increase the amount of material which can deform under load.

Mini Super W Pad

Mini Super W pads feature unique waffle pockets which allow for greater deformation of the material, providing excellent isolation performance. Mini Super W anti-vibration pads can be supplied in multiple configurations to suit most situations.

Open Spring Mounts

Open spring mounts are typically used to isolating mechanical equipment, which producing lower frequency vibrations.

Restrained Spring Mounts

Restrained Spring Mounts are spring mounts supplied with a housing which restricts spring travel. This is useful when equipment is subject to wind loading or changes weight during maintenance.

ND – Double Deflection Rubber Mounts

ND Double Deflection Rubber Mounts are used to isolate mechanical plant and machinery as well as wooden floating floors.

BBNR Bridge Bearing Natural Rubber Pad

BBNR pads are 25mm thick anti-vibration pads that are available in a selection of sizes and load capacities. They can be applied to many applications, from the supporting of mechanical equipment, to the isolation of building structures.

RBA/RCA/RDA Mount

RBA / RCA / RDA mounts are fully captive isolators that can work in any orientation.

BR Restrained Captive Neoprene Mounting

The BR is an all directional captive bridge bearing neoprene mounting for seismic, mobile mounted equipment, marine, and wall hung applications such as commercial garage doors.

PB Panel Board Mounts

PB Panel Board Isolators are used to resiliently mount cabinets or boards to a wall. They are designed to accept a shear loading and isolate the fixing at the same time.

Spring Mounted Inertia Bases

Inertia bases, used in conjunction with the right acoustic isolation system, are the most effective anti-vibration technique for machinery. They can vary from a simple steel frame which allows spring mounts to connect to the equipment, to large concrete filled frames to provide inertial mass.

HLB/HLW – Neoprene Impregnated Duck Isolation Bushings & Washers

Our HLB & HLW Neoprene Impregnated Duck Isolation Bushings & Washers are used to isolate fixings by ensuring that there is no contact between the fixings and the brackets and or parts to be installed.

Air Springs

Air Springs are typically used to isolate equipment that is very sensitive to vibration. They provide very high levels of isolation, can reach very low natural frequencies and are essentially resonance free. They would typically be used in but not limited to, research and medical facilities, and precision manufacturing environments.

Vibration Control

We stock a wide range of vibration control products, designed for all applications and scenarios. Our engineers can help to select an appropriate product, design bespoke systems, and in some cases carry out the installation of vibration control products.

Anti-Vibration Rubber Mounts & Pads

Anti-vibration mounts & pads supplied by Mason U.K. are manufactured from high quality bridge-bearing neoprene or L.D.S rubber. Both materials are certified to meet or exceed applicable standards.

Encased Spring Mounts

Encased Spring Mounts are designed for conditions where stability is a problem, as they incorporate foam inserts to limit movement during equipment start up. They are recommended for compressors, air handling units, centrifugal fans and other constant frequency vibration problems.

Spring Mounts

Mason UK has a complete range of spring mounts both open, enclosed and restrained. Spring mounts are typically used for applications where low frequency (sub 8Hz) vibrations are present.

Pipe Systems & Engineering Products

  • All
  • Building Services (HVAC) Vibration Isolation
  • Flexible Pipe Connectors
  • Mercer Rubber Flexible Connectors
  • Pipework Isolation Accessories
  • Products
  • Rubber Expansion Joints
  • Stainless Steel Flexible Pipe Connectors

Control Rods and Cables

Expansion joints installed in unanchored piping or connected to isolated equipment must have control rods; those control rods must be properly set so that allowable movements are not exceeded.

Thrust Restraints

Thrust restraints are recommended for all fan heads and for axial or centrifugal fans when the air thrust exceeds 10% of the equipment weight.

Ball Joints

Ball joints are used to allow for pipe movement from such scenarios as thermal expansion.

Concentric & Eccentric Reducers

These products are flanged concentric and eccentric reducing expansion joints with spherical arches. The carcass is made of multiple plies of tough, rubber impregnated fabric or tire cord with rubber and duck flanges integral with body.

Mercer Duct Connectors

Flexible Connectors are used in duct systems to reduce vibration transmission and shock and accommodate thermal movements at minimum stress to the ductwork.

VIBRAFLEX 150 Reinforced Rubber Pipe (Fluid Service)

The Mercer Vibraflex reinforced rubber pipe is hand built by our skilled craftsmen. To minimize pipe elongation, the carcass is constructed of multiple plies of high tensile polyester tire cord or Kevlar for high temperatures.

Series 1000 Low Spring Rate, Large Movement Expansion Joints

The Series 1000 are low spring rate, large movement expansion joints for applications where significant movement is required in the pipeline.

Series 800 Teflon Expansion Joints

MERCER Series 800 PTFE Teflon® expansion joints are the sure and economical way to solve difficult expansion and misalignment problems. The Teflon® material is corrosive-proof, chemically inert and does not age.

Series 700 Invincible Teflon Lined Expansion Joints

Mercer Invincible Series 700 Teflon® lined expansion joints combine the advantages of Teflon’s® anti-stick properties, superior strength, excellent chemical resistance and non-aging, with the advantages of Mercer’s elastomeric expansion joints.

Series 500 & 600 Invincible Heavy Duty Expansion Joints

The Mercer Invincible 500 and 600 series are our most rugged expansion joints. They are all hand built by our skilled craftsmen.

Series 450 Flexmore Expansion Joint

Mercer Flexmore Series 450 is the most economical, full-pressure elastomeric expansion joint available. Tough fabric and tirecord plies are bonded between the tube and cover in a steel mould and then cured in a thermostatically controlled steam chamber.

Series 300 Sleeve Type Expansion Joint

Our Mercer series 300 sleeve type expansion joints are available in a large variety of tube and cover material for different applications. Such materials as EPDM, Hypalon, Neoprene, Nitrile and more.

Mercer Connectors

Mercer Rubber Company, established in 1866, is the oldest U.S. manufacturer of rubber expansion joints, flexible duct connectors and industrial hose. All connectors are hand built to the highest standards.

Masonflex Expansion Joints

Masonflex has been sold without interruption for approximately 25 years. In this latest improved version the Kevlar® reinforcement replaces Nylon to greatly reduce elongation and to provide virtual insensitivity to high temperatures.

Building Services (HVAC) Vibration Isolation

We can support the design and engineering of building services requiring vibration isolation, thermal expansion compensation and pipe stress analysis to determine expansion and movement requirements. We have a lot of experience and a proven product range.

Rubber Expansion Joints

There are many types of flexible pipe connectors and expansion joints produced by Mason Industries. This page gives a brief overview with links to more specific product details.

Super Flex Pipe Connectors

Super Flex expansion joints were designed after years of application experience. They are great for vibration & noise control.

Safe Flex Pipe Connectors

The Safeflex flange uses a fully encapsulated square section ring instead of cables. This greatly reduces the risk of failure and eliminates the need for control rods/cables at normal working pressures.

Stainless Steel Flexible Pipe Connectors

Stainless steel connectors are used where movement is required between two pipes or pieces of equipment. They are mainly required when pipes have to bridge building expansion joints or to allow for movement of mechanical equipment.

Expansion Joints

Many expansion joints are custom manufactured to diameters as large as 8 feet (2.4m). We can build to your specific product description or complete our own recommendations based on your movement and pressure requirements. 

Expansion Compensators and Housed Expansion Joints

Expansion Compensators and Housed Expansion Joints are fundamentally a bellows that is protected by and guided within a pipe housing. They are also designed to give improved stability.

Bellows Pump Connectors

All bellows differ from stainless steel hose in the corrugation configurations. Bellows are deeper and wider and they are made from a heavier material to handle the pressure without the braid. A very common location of our 2 ply bellows is at the pumps.

Vee Assemblies

Many buildings are separated by expansion joints through the walls and floors. During an earthquake the two adjacent parts resonate with relatve motion of as much as +/- 100mm in shear as well as toward and away from one another.

Braided Annular Flexible Hose

Mason UK can provide a range of stainless steel braided annular flexible hose. These flexible pipe connectors are suitable for use with corrosive fluids, gases or temperatures and pressures outside of the rubber range.

Flexible Pipe Connectors

There are many types of flexible pipe connectors produced by Mason Industries. They can be broadly categorised into two groups; rubber expansion joints and stainless steel flexible connectors.

Pipe Guides, Anchors & Adjustable Sliding Guides

Mason Adjustable Sliding Guides (ASG) are pipe guides that can be installed in any orientation. They come is a range of standard sizes to suit pipes from 20mm to 300mm in diameter. Larger Guides are available on request. Full details can be found in the attached bulletin below.

Building Isolation Products

  • All
  • Elastomeric Isolation Bearings
  • Isolation Bearing Products
  • Products
  • Structural Isolation Bearings

Elastomeric Isolation Bearings

Elastomeric bearings can be made from a variety of materials and are very effective against most medium to high frequency vibration sources. The material choice depends on the environment, but natural rubber is the most common choice due to its low dynamic stiffness.

Spring Isolation Bearings

Spring bearings are used to isolate against low frequency vibration sources and impact. They can be made using single or multiple springs and low natural frequencies of less than 2.0Hz can be achieved.

Structural Isolation Bearings

Building isolation bearings are used to isolate entire buildings or elements such as walls, floor plates, or columns. Bearings are normally bespoke, designed to accept the specific loads and have the correct isolation characteristics.

  • All
  • Acoustic Foams
  • Air Springs
  • Architectural
  • Building Services (HVAC) Vibration Isolation
  • Concrete Floating Floors
  • Elastomeric Isolation Bearings
  • Flexible Pipe Connectors
  • Floating Floors
  • Inertia Bases
  • Isolated Walls
  • Isolation Bearing Products
  • Isolation Hangers
  • Jack-Up LDS Rubber Floating Floors
  • Jack-Up Spring Floating Floors
  • L.D.S Rubber Hangers
  • Lightweight Floating Floors
  • Mercer Rubber Flexible Connectors
  • MFS Lightweight Floor Spring
  • Products
  • Rubber Expansion Joints
  • Rubber Mounts & Pads
  • Spring Hangers
  • Spring Mounts
  • Stainless Steel Flexible Pipe Connectors
  • Structural Isolation Bearings
  • Vibration Control

CWC-50 Acoustic Ceiling and Wall Clip

A cost-effective solution for vibration isolation and acoustic treatment of walls and ceilings, our new CWC-50 Clip is designed with ease of installation in mind.

Acoustic Floating Floors

Floating floors systems are used for many purposes, predominantly to prevent noise passing through the floor but also to isolate against vibration and impact

Concrete Floating Floors

Floating floors systems are used for many purposes, predominantly to prevent noise passing through the floor but also to isolate against vibration and impact.

Control Rods and Cables

Expansion joints installed in unanchored piping or connected to isolated equipment must have control rods; those control rods must be properly set so that allowable movements are not exceeded.

Concentric & Eccentric Reducers

These products are flanged concentric and eccentric reducing expansion joints with spherical arches. The carcass is made of multiple plies of tough, rubber impregnated fabric or tire cord with rubber and duck flanges integral with body.

Mercer Duct Connectors

Flexible Connectors are used in duct systems to reduce vibration transmission and shock and accommodate thermal movements at minimum stress to the ductwork.

VIBRAFLEX 150 Reinforced Rubber Pipe (Fluid Service)

The Mercer Vibraflex reinforced rubber pipe is hand built by our skilled craftsmen. To minimize pipe elongation, the carcass is constructed of multiple plies of high tensile polyester tire cord or Kevlar for high temperatures.

Series 1000 Low Spring Rate, Large Movement Expansion Joints

The Series 1000 are low spring rate, large movement expansion joints for applications where significant movement is required in the pipeline.

Series 800 Teflon Expansion Joints

MERCER Series 800 PTFE Teflon® expansion joints are the sure and economical way to solve difficult expansion and misalignment problems. The Teflon® material is corrosive-proof, chemically inert and does not age.

Series 700 Invincible Teflon Lined Expansion Joints

Mercer Invincible Series 700 Teflon® lined expansion joints combine the advantages of Teflon’s® anti-stick properties, superior strength, excellent chemical resistance and non-aging, with the advantages of Mercer’s elastomeric expansion joints.

Series 500 & 600 Invincible Heavy Duty Expansion Joints

The Mercer Invincible 500 and 600 series are our most rugged expansion joints. They are all hand built by our skilled craftsmen.

Series 450 Flexmore Expansion Joint

Mercer Flexmore Series 450 is the most economical, full-pressure elastomeric expansion joint available. Tough fabric and tirecord plies are bonded between the tube and cover in a steel mould and then cured in a thermostatically controlled steam chamber.

Series 300 Sleeve Type Expansion Joint

Our Mercer series 300 sleeve type expansion joints are available in a large variety of tube and cover material for different applications. Such materials as EPDM, Hypalon, Neoprene, Nitrile and more.

Mercer Connectors

Mercer Rubber Company, established in 1866, is the oldest U.S. manufacturer of rubber expansion joints, flexible duct connectors and industrial hose. All connectors are hand built to the highest standards.

Masonflex Expansion Joints

Masonflex has been sold without interruption for approximately 25 years. In this latest improved version the Kevlar® reinforcement replaces Nylon to greatly reduce elongation and to provide virtual insensitivity to high temperatures.

MFS-B 25mm Deflection Floor Spring Mount

Our MFS spring mounts are available with higher deflection 25mm springs (titled MFS-B). Utilising our 30-B series springs enables the mounts to achieve lower natural frequencies and therefore improve isolation performance from typical gym activities, compared to the standard MFS mounts.

HDQF-A Rubber Ceiling Hangers

HDQF quick fit ceiling hangers use high quality low dynamic stiffness natural rubber. This hanger has been designed to aid the contractor with a quick and easy installation of suspended acoustic ceilings.

HD LDS Rubber Acoustic Ceiling Hangers

The HD range of hangers is one of our most popular anti-vibration hangers. The acoustic hanger uses a high quality low dynamic stiffness (LDS) natural rubber element which offers excellent acoustic sound isolation properties.

HDQF-X Spring Hanger

HDQF-X quick fit ceiling hanger (Spring Variant). This hanger has been designed to aid the contractor with a quick and easy installation of suspended acoustic ceilings.

30 Series – Acoustic Spring Hanger

The 30 hanger series can be fitted with a range of springs to suit acoustic and weight requirements. Spring hangers are used to isolate against low frequency noise from sources such as footfalls and mechanical vibration.

30N Series – Spring Hanger

The 30N hanger series can be fitted with a range of springs to suit acoustic and weight requirements. Spring hangers are used to isolate against low frequency noise from sources such as footfalls and mechanical vibration.

Rubber Expansion Joints

There are many types of flexible pipe connectors and expansion joints produced by Mason Industries. This page gives a brief overview with links to more specific product details.

Elastomeric Isolation Bearings

Elastomeric bearings can be made from a variety of materials and are very effective against most medium to high frequency vibration sources. The material choice depends on the environment, but natural rubber is the most common choice due to its low dynamic stiffness.

Super Flex Pipe Connectors

Super Flex expansion joints were designed after years of application experience. They are great for vibration & noise control.

Safe Flex Pipe Connectors

The Safeflex flange uses a fully encapsulated square section ring instead of cables. This greatly reduces the risk of failure and eliminates the need for control rods/cables at normal working pressures.

DNSB-A Sway Brace/Wall Tie

DNSB-A is a low frequency wall tie. This sway brace has a bolt end for stud walls or hooked end for masonry walls.

DNSB-BM Wall Tie/Sway Brace

This DNSB-BM is our most popular acoustic sway brace. It is a low frequency wall tie. You have a choice of a bolt end for stud walls or hooked end for masonry walls.

WIC Sway Brace/Wall Tie

The WIC acoustic wall tie is a low profile, low cost sway brace. Minimum cavity = 40mm

WIC-2-SM Sway Brace/Wall Tie

Type WIC-2-SM is a masonry wall tie designed to connect two masonry walls built together. There is no limit on wall thickness or cavity for this sway brace

WIC-2-90 Sway Brace/Wall Tie

The Type WIC-2-90 acoustic sway brace/wall tie is a 90-degree variant of our popular WIC product. It is designed to tie internal and external walls together. One side is designed to be imbedded into blockwork mortar joints, the other to be fixed into the opposing wall with suitable fixings.

DSSB – Double Spring Sway Brace/Slam Wall Isolator

The DSSB Double Spring Sway Brace/ Slam Wall Isolator is a specially designed product, which was first thought up to solve a problem, but become a popular solution for such constructions as slam/rebound walls. As a result of this popularity, we decided to add it to our vast product range.

HDLP-X Low Profile Ceiling Hanger

The HDLP-A Hanger (PREVIOUSLY CALLED THE CRCH-X) has been designed as a low profile ceiling hanger and is used where floor to ceiling heights are critical. It uses the same spring element as the 30-X and HDQF-X Hanger, and therefore has the same properties.

Stainless Steel Flexible Pipe Connectors

Stainless steel connectors are used where movement is required between two pipes or pieces of equipment. They are mainly required when pipes have to bridge building expansion joints or to allow for movement of mechanical equipment.

Expansion Joints

Many expansion joints are custom manufactured to diameters as large as 8 feet (2.4m). We can build to your specific product description or complete our own recommendations based on your movement and pressure requirements. 

Expansion Compensators and Housed Expansion Joints

Expansion Compensators and Housed Expansion Joints are fundamentally a bellows that is protected by and guided within a pipe housing. They are also designed to give improved stability.

Bellows Pump Connectors

All bellows differ from stainless steel hose in the corrugation configurations. Bellows are deeper and wider and they are made from a heavier material to handle the pressure without the braid. A very common location of our 2 ply bellows is at the pumps.

Vee Assemblies

Many buildings are separated by expansion joints through the walls and floors. During an earthquake the two adjacent parts resonate with relatve motion of as much as +/- 100mm in shear as well as toward and away from one another.

Braided Annular Flexible Hose

Mason UK can provide a range of stainless steel braided annular flexible hose. These flexible pipe connectors are suitable for use with corrosive fluids, gases or temperatures and pressures outside of the rubber range.

Flexible Pipe Connectors

There are many types of flexible pipe connectors produced by Mason Industries. They can be broadly categorised into two groups; rubber expansion joints and stainless steel flexible connectors.

MFS-AJ Adjustable Floor Spring

The MFS-AJ is a jack specially built for attachment to joists and its used as part of a lightweight acoustic floating floor system. The ability to adjust the height gives it an advantage over the standard MFS when placing jacks on floors that aren’t level.

MFS-AF Adjustable Floor Spring

The MFS-AF is an acoustic floating floor jack specifically built for lightweight floors. The ability to adjust the height gives it an advantage over the standard MFS when placing jacks on floors that aren’t level.

MFS Lightweight Floor Spring

It is often necessary to provide an wooden acoustic floating floor rather than the heavier concrete construction with wood topping. Cost or weight restrictions may be the factor.

Dry and Formwork Acoustic Floor Systems

The best performing floating floor systems are typically heavy and thick, using a concrete layer, such as our jack up floating floors. However, sometimes this is undesirable, or not possible due to structural and building limitations, and a lightweight system is required.

AB-716 Angle Head Restraint

The AB-716 is an angled, head restraint for the top / and of block and stud walls.

NPS – Partition Support

NPS Partition Support isolates the bottom channel of steel stud walls. NPS is held in place by a frame or hammer fixing.

SWW Masonry Isolation

Mason’s SWW type acoustic wall isolation strips are designed to isolate a wall from the base slab. The SWW is designed to suit width and wall load.

AFA – Acoustical Furring Attachment

This AFA is a acoustical furring attachment for use with metal or wood stud walling. It uses a low dynamic stiffness natural rubber for effective isolation and the metal elements of the AFA are completely encapsulated.

Acoustic Isolation Products for Walls

It is important that the walls of a space sensitive to noise or vibration transmission are isolated from the main building structure. These acoustically isolated walls can be built on a floating floor or specially designed wall support plates.

Super W Pad

Super W pads feature unique waffle pockets which allow for greater deformation of the material, providing excellent isolation performance. Super W anti-vibration pads can be supplied in multiple configurations to suit most situations.

HDSM-X Spring Joist Hanger

Joist or wall hanger with 25mm deflection spring element. They can be fitted with a ceiling channel clamp or eye bolt.

HG Grommets Bolt Isolation Bushings

HG Grommets are rubber bolt isolation washer bushings designed to allow a fixing to be passed through without compromising the benefits of an anti-vibration layer.

W Pad

Waffle pad is a thin anti-vibration mat featuring a series of square cut outs which increase the amount of material which can deform under load.

Mini Super W Pad

Mini Super W pads feature unique waffle pockets which allow for greater deformation of the material, providing excellent isolation performance. Mini Super W anti-vibration pads can be supplied in multiple configurations to suit most situations.

HDLP-A Low Profile Ceiling Hanger

The HDLP-A Hanger (PREVIOUSLY CALLED CRCH) has been designed as a low profile ceiling hanger and is used where floor to ceiling heights are critical. It uses the same rubber element as the HD-A and HDQF-A Hanger, and therefore has the same properties.

HDSM-A Joist Hanger

Joist or wall hanger with double deflection LDS rubber element and can be fitted with a ceiling channel clamp or eye bolt.

DNHS – Acoustic Spring Hanger

The DNHS series of hanger features both a metal spring and an LDS rubber element. This provides acoustic isolation against both low and high frequency vibration.

HS – Spring Hanger

The HS series of spring hanger allows for a wide range of springs to be used to suit both acoustic and load requirements.

Open Spring Mounts

Open spring mounts are typically used to isolating mechanical equipment, which producing lower frequency vibrations.

Restrained Spring Mounts

Restrained Spring Mounts are spring mounts supplied with a housing which restricts spring travel. This is useful when equipment is subject to wind loading or changes weight during maintenance.

ND – Double Deflection Rubber Mounts

ND Double Deflection Rubber Mounts are used to isolate mechanical plant and machinery as well as wooden floating floors.

BBNR Bridge Bearing Natural Rubber Pad

BBNR pads are 25mm thick anti-vibration pads that are available in a selection of sizes and load capacities. They can be applied to many applications, from the supporting of mechanical equipment, to the isolation of building structures.

RBA/RCA/RDA Mount

RBA / RCA / RDA mounts are fully captive isolators that can work in any orientation.

BR Restrained Captive Neoprene Mounting

The BR is an all directional captive bridge bearing neoprene mounting for seismic, mobile mounted equipment, marine, and wall hung applications such as commercial garage doors.

PB Panel Board Mounts

PB Panel Board Isolators are used to resiliently mount cabinets or boards to a wall. They are designed to accept a shear loading and isolate the fixing at the same time.

Spring Mounted Inertia Bases

Inertia bases, used in conjunction with the right acoustic isolation system, are the most effective anti-vibration technique for machinery. They can vary from a simple steel frame which allows spring mounts to connect to the equipment, to large concrete filled frames to provide inertial mass.

Jack-Up LDS Rubber Floating Floors

The Mason FSN Jack-Up acoustic floor system can be used as the crucial part of achieving box in box construction for studios or rooms requiring a high level of acoustic separation or simply providing acoustic or impact isolation from one area to another.

Jack-Up Spring Floating Floors

The jack up spring floating floor is used for low frequency isolation or where impact isolation is required, such as bowling alleys, gymnasia and health clubs.

HLB/HLW – Neoprene Impregnated Duck Isolation Bushings & Washers

Our HLB & HLW Neoprene Impregnated Duck Isolation Bushings & Washers are used to isolate fixings by ensuring that there is no contact between the fixings and the brackets and or parts to be installed.

WHR Acoustic Ceiling Hangers

The WHR is a low cost ceiling hanger which still provides 5mm of deflection and is constructed from high quality low dynamic stiffness natural rubber which has natural acoustic isolation properties.

Air Springs

Air Springs are typically used to isolate equipment that is very sensitive to vibration. They provide very high levels of isolation, can reach very low natural frequencies and are essentially resonance free. They would typically be used in but not limited to, research and medical facilities, and precision manufacturing environments.

Vibration Control

We stock a wide range of vibration control products, designed for all applications and scenarios. Our engineers can help to select an appropriate product, design bespoke systems, and in some cases carry out the installation of vibration control products.

NFS – Neoprene Foam Strip

Closed cell foams are used as part of an airborne acoustic barrier or a structural vibration break.

Anti-Vibration Rubber Mounts & Pads

Anti-vibration mounts & pads supplied by Mason U.K. are manufactured from high quality bridge-bearing neoprene or L.D.S rubber. Both materials are certified to meet or exceed applicable standards.

Isolation Hangers

Acoustic isolation hangers are an excellent way of preventing airborne noise from below passing into the building structure, or preventing noise/vibration from the floor above entering the room below.

Dry and Formwork Rubber Floating Floor

The Dry Rubber Floating Floor system is the traditional method of creating a floating floor. Isolators are placed at regular intervals across the area and the floating floor built on top.

Spring Hangers

Mason U.K. has a large range of spring hangers available to suit a wide variety of loads and acoustic requirements.

L.D.S Rubber Hangers

Acoustic, LDS (Low Dynamic Stiffness) rubber (previously neoprene) hangers can be used for suspending ceilings or mechanical plant.

Encased Spring Mounts

Encased Spring Mounts are designed for conditions where stability is a problem, as they incorporate foam inserts to limit movement during equipment start up. They are recommended for compressors, air handling units, centrifugal fans and other constant frequency vibration problems.

Spring Mounts

Mason UK has a complete range of spring mounts both open, enclosed and restrained. Spring mounts are typically used for applications where low frequency (sub 8Hz) vibrations are present.

Spring Isolation Bearings

Spring bearings are used to isolate against low frequency vibration sources and impact. They can be made using single or multiple springs and low natural frequencies of less than 2.0Hz can be achieved.

Structural Isolation Bearings

Building isolation bearings are used to isolate entire buildings or elements such as walls, floor plates, or columns. Bearings are normally bespoke, designed to accept the specific loads and have the correct isolation characteristics.